How to check spark plug wires. - Fuelly Forums

Click here to see important news regarding the aCar App

Reply
 
Thread Tools Display Modes
 
Old 12-16-2005, 03:28 PM   #1
Registered Member
 
Join Date: Nov 2005
Posts: 34
Country: United States
How to check spark plug wires.

My spark plug wires were so bad...
How bad were they?
They were causing the coil to burn out...I guess from being overvoltaged.
How do I check my spark plug wires, if I don't know the expected resistance value for them?
Connect a timing light to each wire(near the plug), and compare the strength and regularity of the strobe produced. If possible check a car with a quality set of spark plug wires to see how well the timing light COULD perform if the inducted signal from the spark plug wires was quality. Doing this in a darkened area like a garage with the light out, or at night would probably dramatise the differences between the light produced by the stobe on each wire. My wires could have been 5 or 10 years old, and the light produced by the stobe was irregular and about half as bright as that produced by a fresh set of high performance wires. The stobe from the old wires was so bad...that the timing light could have been misdiagnosed as malfunctioning.
__________________

CruiseControl is offline   Reply With Quote
Old 12-16-2005, 07:04 PM   #2
Registered Member
 
Join Date: Oct 2005
Posts: 1,978
Country: United States
How many miles?

How many miles on the wires and which vehicle? Was it running rough?

RH77
__________________

__________________
rh77 is offline   Reply With Quote
Old 12-23-2005, 06:47 PM   #3
Registered Member
 
Join Date: Nov 2005
Posts: 34
Country: United States
It was running soooo rough...

It was running so rough, that the dealer said it needed a valve adjustment! 94 Honda Civic, and I think the wires were replaced once. Thier resistance values were, 1 & 2 wire ~ 12K ohms, and the 3 & 4 wire ~ 8K ohms. 4K ohms seems like a large difference in resistances.
CruiseControl is offline   Reply With Quote
Old 12-23-2005, 10:54 PM   #4
Registered Member
 
Join Date: Dec 2005
Posts: 8
Country: United States
Checking plug wires

Question - did you check resistance on the new wires to compare to the old wires? Generally speaking isn't values to 12k ohms acceptable? If wires leak voltage to ground, the engine will get an intermittant miss. Worse cases the leaks are visible at night with the hood open. Anyhow, what are the values of resistance on your new replacement wires? Ken
GasSavers_KenS is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Replace HWY/City w/ Avg Speed? ekobres General Fuel Topics 5 03-06-2013 05:31 AM
Not very precise mpg calculation larjerr Fuelly Web Support and Community News 4 08-20-2012 01:03 AM
US / metric switching problems gory Fuelly Web Support and Community News 4 01-24-2011 02:04 AM
TDI EPA figures off? bates General Fuel Topics 14 09-15-2009 08:04 AM
Low Rolling Resistance Tires SVOboy General Fuel Topics 33 04-04-2006 07:57 PM

» Fuelly iOS Apps
Powered by vBadvanced CMPS v3.2.3


All times are GMT -8. The time now is 01:45 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.