Removing the crankshaft pully... ARGH! - Fuelly Forums

Click here to see important news regarding the aCar App

Reply
 
Thread Tools Display Modes
 
Old 04-16-2006, 04:38 PM   #1
Driving on E
 
Matt Timion's Avatar
 
Join Date: Sep 2005
Posts: 3,110
Country: United States
Removing the crankshaft pully... ARGH!

I just can't do it.

My new engine is sitting in my garage and I figured I should replace the timing belt and water pump before I throw it in my car.

The damn bolt holding the crankshaft pully on won't budge.

At first I stuck a prybar and a screwdriver in the hole to offer some sort of resistance. The end result was a bent screwdriver and prybar.

Today I hooked up the air tools to try to move the thing. Nothing.

Does anyone have a secret (maybe with pictures?) on how to get this thing to budge? My next plan is to just take it to a mechanic and pay them to do it for me.
__________________

Matt Timion is offline   Reply With Quote
Old 04-16-2006, 04:44 PM   #2
FE nut
 
diamondlarry's Avatar
 
Join Date: Sep 2005
Posts: 1,020
Country: United States
It seems that someone here,

It seems that someone here, perhaps Dax?, mentioned something about sticking something in the teeth of the flywheel and getting a 3' or 4' prybar and doing a lot of jumping up and down.
__________________

__________________
Horsepower is how hard you hit the wall, torque is how much of the wall you take with you.

2007 Prius,



Team Slow Burn
diamondlarry is offline   Reply With Quote
Old 04-16-2006, 06:13 PM   #3
Registered Member
 
JanGeo's Avatar
 
Join Date: Jan 2006
Posts: 2,444
Country: United States
Location: Tiverton, RI
Send a message via Yahoo to JanGeo
pulley

My brother says that you need a 500-600 ft-lbs air impact wrench to crack it loose - for some reason the bolt seizes on the crank. This came up when I asked about my friends timing belt change.
JanGeo is offline   Reply With Quote
Old 04-16-2006, 06:30 PM   #4
Registered Member
 
Bunger's Avatar
 
Join Date: Feb 2006
Posts: 311
Country: United States
With the air tools did you

With the air tools did you try all the following:

1. Crank the air pressure to about 120psi, this is probably 30psi over the rating on your gun, but it should take it.

2. Tighten, loosen, tighten, loosen... sometimes does the trick.

3. Are your air tools lubed? Seems to help out a little bit.

4. Are you using impact sockets? Normal sockets will not deliver as much torque to the bolt. (normal sockets flex more, thus absorbing some of the twisting force)

5. PB Blaster on the bolt

I hope these help!!
__________________
Anger is a gift!
- Zack de la Rocha
Bunger is offline   Reply With Quote
Old 04-16-2006, 06:31 PM   #5
Registered Member
 
Join Date: Apr 2006
Posts: 270
Country: United States
Send a message via AIM to molecule
it once took an 11ft bar to

it once took an 11ft bar to break a honda pulley bolt loose...
9ft didn't work !!!

also a socket extension fits perfectly in the pulley hole and will not bend...however it can crack the lip of the block/oilpan

high tq impact wrench is recommended
followed by long *** breakerbar (may require welding...lollercopter)
__________________
BE ZEITGEISTED
molecule is offline   Reply With Quote
Old 04-16-2006, 06:37 PM   #6
Registered Member
 
MetroMPG's Avatar
 
Join Date: Dec 2005
Posts: 4,223
Country: United States
went thru the same thing

went thru the same thing with my accord. ended up taking it to the garage and the mechanic used his (better) impact wrench to break the seal. he was nice about it though - just had me pull up to the bay and he got it through the access hole in the fender well and wouldn't take any money.
MetroMPG is offline   Reply With Quote
Old 04-16-2006, 08:18 PM   #7
Registered Member
 
JanGeo's Avatar
 
Join Date: Jan 2006
Posts: 2,444
Country: United States
Location: Tiverton, RI
Send a message via Yahoo to JanGeo
ARG

Ahhh professional courtesy is alive and well.
JanGeo is offline   Reply With Quote
Old 04-16-2006, 08:24 PM   #8
Registered Member
 
Join Date: Nov 2005
Posts: 331
Country: United States
Send a message via MSN to n0rt0npr0
Right on Bunger. You need

Right on Bunger.

You need that 120psi.
You need decent impact sockets.
The impact wrench should be lubed well.
Try not to use extensions.
Then, Tighten, loosen, tighten, loosen. And stay flush dead on that bolt head so you transfer all that energy upon your nemesis.
Fun stuff
__________________
"You have to know the truth, and seek the truth, and the truth will set you free."
-unknown
n0rt0npr0 is offline   Reply With Quote
Old 04-16-2006, 08:53 PM   #9
Driving on E
 
Matt Timion's Avatar
 
Join Date: Sep 2005
Posts: 3,110
Country: United States
Re: With the air tools did you

Quote:
Originally Posted by Bunger
With the air tools did you try all the following:

1. Crank the air pressure to about 120psi, this is probably 30psi over the rating on your gun, but it should take it.
The gun is rated at 90psi, so I did stop at 80. I'll try cranking it up to 120 tomorrow.

Quote:
Originally Posted by Bunger
2. Tighten, loosen, tighten, loosen... sometimes does the trick.
Tried this a little bit, but not too much. WIll try more with the 120psi tomorrow.
Quote:
Originally Posted by Bunger

3. Are your air tools lubed? Seems to help out a little bit.
Air tools are fairly new, only been used twice. I'll lube it up though for good measure.

Quote:
Originally Posted by Bunger
4. Are you using impact sockets? Normal sockets will not deliver as much torque to the bolt. (normal sockets flex more, thus absorbing some of the twisting force)
Using an impact socket, yes.

Quote:
Originally Posted by Bunger
5. PB Blaster on the bolt
I did this before the impact gun.

I'll be trying this again tomorrow, and then I'll be taking it to the shop down the street from me. Do you think I can lift a motor into my trunk? It doesn't seem that heavy.

BTW, does anyone know what I torque this bolt to once I'm done changing the timing belt?
Matt Timion is offline   Reply With Quote
Old 04-16-2006, 09:18 PM   #10
Registered Member
 
Bunger's Avatar
 
Join Date: Feb 2006
Posts: 311
Country: United States
Re: With the air tools did you

Quote:
Originally Posted by Matt Timion
The gun is rated at 90psi, so I did stop at 80. I'll try cranking it up to 120 tomorrow.

I'll be trying this again tomorrow, and then I'll be taking it to the shop down the street from me. Do you think I can lift a motor into my trunk? It doesn't seem that heavy.

BTW, does anyone know what I torque this bolt to once I'm done changing the timing belt?
I've gone as high as 150 psi before... dunno how good that is for the hammers, but I've had the same tools for 6 years now, and they are still working ok. =)

Are you lifting the entire motor or just a short block? The entire thing can be a bit much for a single person.

119 ft/lbs on the crank pulley bolt.
__________________

__________________
Anger is a gift!
- Zack de la Rocha
Bunger is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Fuelly iOS Apps
Powered by vBadvanced CMPS v3.2.3


All times are GMT -8. The time now is 02:08 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.