Drafting behind a Truck - Fuelly Forums

Click here to see important news regarding the aCar App

Reply
 
Thread Tools Display Modes
 
Old 09-21-2006, 04:13 PM   #1
Registered Member
 
GasSavers_roadrunner's Avatar
 
Join Date: Sep 2006
Posts: 109
Country: United States
Location: Perkasie, PA
Drafting behind a Truck

I am still waiting to get my Yaris Hatchback, then I will get a scangauge. If I had my ride and my scangauge I would do this test myself.
Has anyone tried drafting a truck on the highway to see how much it improved their gas mileage? How close to the truck did you need to get?
Roadrunner
__________________

GasSavers_roadrunner is offline   Reply With Quote
Old 09-21-2006, 05:00 PM   #2
Registered Member
 
Join Date: Oct 2005
Posts: 1,978
Country: United States
Better go with ACME

Quote:
Originally Posted by roadrunner
I am still waiting to get my Yaris Hatchback, then I will get a scangauge. If I had my ride and my scangauge I would do this test myself.
Has anyone tried drafting a truck on the highway to see how much it improved their gas mileage? How close to the truck did you need to get?
Roadrunner
Unfortunately, the closer the better, but more dangerous. A study was done recently that showed that the bumper-bar on most trailers is insufficent, and is just the right height to slice your head off in a rear-end collision.

There's a safer "side-draft" technique that's still in the DOT's "No-Zone" as well -- position the vehicle in the lane next to the semi at about where the trailer attaches. This is a bad spot too because it will certainly irritate the truck driver and/or may merge into you.

The best way is the "ACME" claw arm, or the more expensive LECTRO-magnet system (worse for FE, I've found -- take a lot of juice to power up that bad boy).

RH77
__________________

__________________
rh77 is offline   Reply With Quote
Old 09-21-2006, 05:12 PM   #3
Registered Member
 
schmeep's Avatar
 
Join Date: Aug 2006
Posts: 65
Country: United States
drafting behind a truck is for the suicidal, it isn't worth it to save a bit of gas, i hope no one here does this or promotes the idea.
__________________
schmeep is offline   Reply With Quote
Old 09-21-2006, 05:37 PM   #4
Registered Member
 
kickflipjr's Avatar
 
Join Date: Sep 2005
Posts: 933
Country: United States
I heard long distance drafting (around 1 second behind) still has some advantages. It still is dangerous but not as bad as being 5' behind.
__________________
2008 EPA adjusted:


Distance traveled by bicycle in 2007= 1,830ish miles
Average commute speed=25mph (yes, that's in a car)
kickflipjr is offline   Reply With Quote
Old 09-21-2006, 05:40 PM   #5
Registered Member
 
JanGeo's Avatar
 
Join Date: Jan 2006
Posts: 2,444
Country: United States
Location: Tiverton, RI
Send a message via Yahoo to JanGeo
You can benefit from 2 to 3 seconds behind trucks and in the lanes to either side of them and the more trucks form in front of you in a convoy fashion and the faster they go i.e. 70mph the more they knock down the wind in front of you and the further behind them it extends so you can safely follow in their wake. Unfortunately you have to breath the exhost fumes and in rainy conditions the dirt they throw up in the mist they create. As far as safety is concerned they usually don't stop suddenly so in that respect they are safe to follow but you need to make sure you allow them room to change lanes should they need to. Getting too close to them is also a great way to add holes to your front paint job and windshield as they do tend to kick up road junk and rocks. Jeeps and pickup trucks are the only vehicles which throw more rocks with their rear tires than semi's because they usually don't have any mud flaps and are jacked up pretty high exposing the rear tread. The first chips in my new xB windshield was from a pickup truck passing me and changing lanes in front of me too close on an empty highway.
JanGeo is offline   Reply With Quote
Old 09-21-2006, 05:43 PM   #6
Senior Member
 
BumblingB's Avatar
 
Join Date: Feb 2009
Posts: 341
Country: United States
Location: NW Florida
Drafting isn't safe and the truck drivers hate it. You'll know when they ride the outer line to kick trash/rocks up on your car. (I sometimes drive a truck for work as a last resort if they can't get anyone else-CDL)

That being said, I have done it at a fairly safe distance at around 65MPH in a 70 zone and gotten 42 with my Matrix when I normal got 37 on the same route. Even at a safe distance its still white knuckle driving that I don't find relaxing. I seldom do it anymore EXCEPT when the beer trucks pull out in front of me in the morning when I'm going to work. The trailers are MUCH more low profile and cut through the air making a great clear path AND remember, they cut in front of me which makes it OK to tailgate - not - its still not right to draft whether I do it or not ( ).
BumblingB is offline   Reply With Quote
Old 09-21-2006, 06:19 PM   #7
Registered Member
 
Join Date: Oct 2005
Posts: 1,978
Country: United States
Quote:
Originally Posted by JanGeo
The first chips in my new xB windshield was from a pickup truck passing me and changing lanes in front of me too close on an empty highway.
I kid you not, 20 miles on the odometer of the TSX and a ratty old gravel truck merges onto the highway, hits a bump, and sends gravel flying. Now, I have scratches down to the primer on the hood and dimples in the bumper

I know you can't keep a car new forever, but c'mon!!!

No license plate on the truck, and we weren't getting any closer to get the hauler name. A little touch-up paint helped, but

RH77
__________________
rh77 is offline   Reply With Quote
Old 09-21-2006, 07:24 PM   #8
Registered Member
 
Join Date: Oct 2005
Posts: 1,978
Country: United States
Quote:
Originally Posted by theclencher
Every time I go through Ohio some dingus either runs into me or throws up rocks that break my windshield. I hate Ohio.
OK, now it's personal. Born in Barberton, Ohio, Alma Mater: Muskingum College, New Concord, Ohio. Folks live in Ohio.

Yeah, come to think, I don't like it there either, that's why I moved away...

Nevermind...

RH77
__________________
rh77 is offline   Reply With Quote
Old 09-21-2006, 10:27 PM   #9
Registered Member
 
tomauto's Avatar
 
Join Date: Apr 2006
Posts: 292
Country: United States
Send a message via AIM to tomauto Send a message via MSN to tomauto Send a message via Yahoo to tomauto
I always wanted to make a little grapple for the lower bar on the truck trailer...for my long trips it seems like a money saving opportunity
__________________
Current Stable
GasSaver: 2000 Honda Insight Silverstone w/AC 65+mpg
Track Terror: 2002 Honda S2000 Gran Prix White- lots of mods - 28mpg
Beater: 1988 Honda Civic DX Hatback - Stripped - 30mpg

RIP: 1996 Honda Civic LX 42mpg - you will be missed

https://tomauto.smugmug.com/Cars
tomauto is offline   Reply With Quote
Old 09-21-2006, 10:49 PM   #10
Registered Member
 
Join Date: Oct 2005
Posts: 1,978
Country: United States
Quote:
Originally Posted by tomauto
I always wanted to make a little grapple for the lower bar on the truck trailer...for my long trips it seems like a money saving opportunity
...And it's technically carpooling

RH77
__________________

__________________
rh77 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
LPG or twin tank systems... Speedtorque General Fuel Topics 3 08-11-2011 09:28 AM
Partial fuel-up - when do you reset your trip odometer? johnclayton Fuelly Web Support and Community News 2 07-30-2009 09:16 PM
drivetrain resistance bagpipe goatee General Fuel Topics 9 09-14-2008 09:04 PM
Feature Request: City vs Highway jethrographic Fuelly Web Support and Community News 1 08-08-2008 09:43 AM
How did you first find Gassavers.org? kickflipjr General Discussion (Off-Topic) 17 05-24-2006 07:28 PM

» Fuelly Android Apps
Powered by vBadvanced CMPS v3.2.3


All times are GMT -8. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.